 |
 |
||
 |
 |
 |
|
 |
 |
 |
|
Thermcoat
Mechanical Equipment Room (M.E.R.) Coating
Therm Coat 2000 Data Sheet
Elastomeric Ceramic Roof Coating
COMPOSITION:
Therm Coat 2000 Acrylic Elastomeric Roof Coating is a single component high-solids, water-based acrylic coating, specially formulated with ceramics to provide an insulating barrier system.
BASIC USE:
Therm Coat 2000 is designed to be installed over metal roofing, urethane form roofing, membrane roofing and composition shingle roofing. Therm Coat 2000 is elastomeric and provides durable protection from ultraviolet light exposure and allows for easy maintenance of the membrane.
TECHNICAL DATA:
SOLIDS BY VOLUME: 50%APPLICATION RATE: 65 Sq. Ft. Per Gal @ 12 mils DFTELONGATION: 125% at 70° FLEXIBILITY: 180-degree bend at 0°
WEATHERABILITY: 2000 hours no wrinkling or shrinking.
PACKAGING:
Therm Coat 2000 is available in 1, 5, and 33-gallon containers (U.S. gallon measures).
SHELF-LIFE:
Twelve months from shipping date and stored below 800 F. Do not allow product to freeze.
COLORS:
Therm Coat 2000 is available in white. Color matching is available upon request at an additional charge. Minimum quantities may apply; overages will apply.
JOB CONDITIONS:
Before any installation is started, the contractor shall thoroughly examine all surfaces for any deficiencies. Should any deficiencies exist, the architect, owner or general contractor shall be notified in writing and any corrections necessary shall be made.
Cold or inclement weather will effect the cure time of this product. Do not install over wet substrate, in the rain or if the threat of rain exists within 24 hours.
INSTALLATION:
Preparation: Metal Roofs
Inspect the roof deck and tighten all loose fasteners. Replace all missing or stripped fasteners with oversized fasteners. Before installing replacement fasteners, spot prime the metal surface under new fastener locations with Excel-Coat Primer MCU-100.
Loose rust should be removed and surface primed with Excel-Coat Primer MCU-100 at 4.0 mils DFT.
Application:
Cover all seams with Butyl Deck Seal Tape. Using 4" wide tape to provide a two-inch overlap on each side of the seam.
Therm Coat 2000 should then be applied in two twelve mil. coats DFT minimum by rolling or spray. If spray equipment is used, carbide tips are recommended.
Preparation: Asphalt Base/Composition Roof
Thoroughly clean the existing roof substrate before application of the coating. The roof must be clean, sound, dry and free of any contaminating materials that would interfere with proper adhesion of the coating. This may require water blasting, scrubbing, power brooming or vacuuming.
Application:
Therm Coat 2000 should then be applied in two twelve mil. coats DFT minimum by rolling or spray. If spray equipment is used, carbide tips are recommended.
Preparation: Urethane Foam Roof
All surface to be coated must be clean, sound, dry of any dirt, grease, oil, debris or other contaminants. Before application, brush with a stiff bristle broom to a clean, sound surface.
Application:
Therm Coat 2000 should then be applied in two twelve mil. coats DFT minimum by rolling or spray. If spray equipment is used, carbide tips are recommended.
Caution: Do not start application where adverse conditions are forecast; specifically rain or temperatures below 55º degrees F or above 90° degrees F. Areas to be coated should be moisture free and dry.
STORAGE AND HANDLING:
Store Therm Coat 2000 in a cool dry area and protect it from freezing. It may be necessary to stir Excel Coat 2000 prior to use. Containers should be separated according to batch numbers. When using more then one batch for the same project, all material should be blended to ensure color uniformity. Partial containers of Therm Coat 2000 can be resealed. Clean mixing and application tools with water. Dispose of empty containers according to current Local, State and Federal regulations.
Repairs and Maintenance:
If damage or wear occur, simple repairs using the same product can be accomplished. Contact Excellent Coatings, Inc. for specific information regarding long term maintenance. Cleaning can be accomplished by scrubbing with normal detergent and water. Power washing and brushing may be required to remove heavy stains.
AVAILABILITY:
Products are immediately available from Excellent Coatings, Inc. and authorized distributors.
COST:
Cost data is available from your Excellent Coatings, Inc. authorized representative. For the name and number of the nearest local representative call Excellent Coatings, Inc. at
(800) 473-3817.
PRODUCT GUARANTEE/WARRANTY:
Excellent Coatings, Inc. warrants Therm Coat to be free of defects and manufactured to meet published physical properties for a period of one year following the date of shipment, provided that the product has been applied according to the manufacturer's instructions. Under the warranty, Excellent Coatings, Inc. will provide, at no charge, product in containers to replace any product proven to be defective in applications recommended by us as suitable for this product. All claims concerning the products' defects must be made within 12 months of shipment and within 30 days of discovery. Absence of such claims in writing during this period will constitute a waiver of all claims with respect to such product. This warranty is IN LIEU of any and all other warranties, expressed or implied, including, but not limited to, any implied warranty of MERCHANTABLITY of fitness for a specific purpose.
Authorized local representatives are available to provide design assistance and on site instructions for our products. Excellent Coatings, Inc. can provide assistance in design and development of special applications and partial inspection. Part-time and full-time inspection is available on a fee basis upon arrangement. Technical Data available upon request.
10/01
 |
 |
 |
 |
 |
 |
 |