Wallguard 3000                                                                            Data Sheet

 

Composition:

Wallguard is an acrylic polymer, single component, durable, flexible membrane. The coating is installed in two coats to create a uniform waterproof membrane that becomes part of the wall system.

 

Basic Use:

Wallguard 3000 is designed to be installed over stucco, wood or concrete surfaces. Wallguard is elastomeric and provides durable protection from ultraviolet light exposure and allows for easy maintenance of the membrane.

 

Limitations:

Do not apply over non-structural substrates. Do not apply below-grade or in areas that are constantly submerged.

 

Grade:

Wallguard 3000 is a single component acrylic wall coating. When desired, a coat of Wallguard 3100 TX can be applied to add a texture coat. Excel-Coat Patching Compound is used to assist in wall preparation prior to application of Wallguard 3000.

 

Packaging:

Wallguard 3000 and Wallguard 3100 TX are available in 1 and 5 gallon containers (U.S. gallon measures). Primer and patching compound are sold in various sizes and quantities.

 

Shelf-life:

12 months from shipping date, stored below 80F. Do not allow product to freeze.

 

Colors:

White, beige and gray. Color matching is available upon request at an additional charge. Minimum quantities may apply; overages will apply.

 

Job Conditions:

Before any installation is started, the contractor shall thoroughly examine all surfaces for any deficiencies. If any deficiencies exist, the architect, owner and general contractor shall be notified in writing and corrections necessary shall be made prior to application.

 

Cold or inclement weather will effect the cure time of all Excel-Coat products.  Do not install over wet substrate, in the rain or if the threat of rain exists within 24 hours.

 

Installation:

Preparation:

A.       Pressure clean all areas to be coated, to remove any debris, dust, stain, loose areas, and any peeling of existing coating.

B.       Mildew and fungus should be removed with detergent soap or bleach and rinsed off thoroughly with clean water.

C.       Patch and repair all voids and delaminated or damaged areas in the wall with Excel-Crete.

D.       Cracks of less than 1/16" should be treated with Excel Coat Patching Compound and spread tightly into the cracks using a patching (bondo) spreader. Cracks that are 1/16" or wider should be tooled and routed to a minimum 1/4" by 1/4" joint and filled with an elastomeric sealant. Where movement is expected, it is recommended to embed tape with the sealant.

E.        Wood windows, doors, sills, columns and protrusions in the plane of the wall should be sanded. Using the Excel-Coat Patching Compound fill all holes, cracks and voids and apply Excel-Coat Primer 120 or PC-155 to the surface. Apply a coat of Wallguard 3000 as a detail coat over all horizontal surfaces, and wall intersections.

F.        Mask and protect all adjacent areas from spills and overspray during application.

G.       Any rough surface should be smoothed by grinding or filled with an appropriate cementitious material such as Excel-Crete.

H.       Rust should be removed, the area repaired and primed with Excel-Coat Primer 120 or PC-155.

 

Application:

A.       Using a roller or spray equipment apply Excel-Coat Primer 120 or PC-155 to all areas to be coated.

B.       Apply two uniform coats using a minimum of 1 gallon of Wallguard 3000 per 100 square feet per coat. Coverage may vary depending on the porosity of the substrate and the application method. Wallguard 3000 and Wallguard 3100 TX can be applied by roller or spray equipment. Minimum dry mils. of both coats should be 15 mils. The second coat can be applied only after the first coat is thoroughly dried.

 

Caution:  Do not start application where adverse weather conditions are forecast; specifically rain or temperatures below 55°F or above 90°F. Areas to be coated should be moisture free and dry. 

 

Storage and Handling:

Store Wallguard in a cool, dry area and protect it from freezing. It may be necessary to stir Wallguard prior to use.  Containers should be separated according to batch numbers. When using more then one batch for the same project, all material should be blended to ensure color uniformity. Partial containers of Wallguard can be resealed. Clean mixing and application tools with water.  Dispose of empty containers according to current Local, State, and Federal regulations.

 

Repairs and Maintenance:

If damage or wear occur, simple repairs using the same product can be accomplished. Contact Excellent Coatings, Inc. for specific information regarding long term maintenance. Cleaning can be accomplished by scrubbing with detergent soap and water. Power washing and brushing may be required to remove heavy stains.

 

availability:

Immediately available from Excellent Coatings, Inc. and authorized distributors.

 

COST:

Cost data is available from your local Excellent Coatings, Inc. authorized representative. For the name and number of the nearest local representative, call Excellent Coatings, Inc. at (800) 473-3817.

 

PRODUCT Guarantee/ Warranty:

Excellent Coatings, Inc. warrants Wallguard to be free of defects and manufactured to meet published physical properties for a period of one year following the date of shipment, provided that the product has been applied according to the manufacturer's instructions. Under the warranty, Excellent Coatings, Inc. will provide, at no charge, product in containers to replace any product proven to be defective in applications recommended by us as suitable for this product. All claims concerning the products' defects must be made within 12 months of shipment and within 30 days of discovery. Absence of such claims in writing during this period will constitute a waiver of all claims with respect to such product. This warranty is  IN LIEU of any and all other warranties, expressed or implied, including, but not limited to, any implied warranty of MERCHANTABLITY of fitness for a specific purpose.

 

Technical Service:

Authorized local representatives are available to provide design assistance and on site instructions for Authorized local representatives are available to provide design assistance and on site instructions for our products. Excellent Coatings, Inc. can provide assistance in design and development of special applications and partial inspection. Part-time and full-time inspection is available on a fee basis upon arrangement Technical Data available upon request.

 

 

 

10/01