SECTION 1 - COMPANY
& PRODUCT IDENTIFICATION
Manufacturer's
Name: Excellent Coatings,
Inc. Prep
Date: 03/01/01
Address:
1285
Distribution Way
Vista,
CA 92083
(800)
473-3817
Product
Class: Epoxy Hardener
Trade
Name:
Prime-Crete Primer PC-155 Part B Hardener
H.M.I.S.
Codes: H
F R P
3 3
0 -
SECTION 2 - HAZARDOUS
INGREDIENTS
Weight Occupt. Exposure Limits Vapor Pressure
Ingredient C.A.S.# Percent OSHA PEL ACGIH
TLV mm Hg & Temp.F
--------------------------------------------------------------------------------------------------------------------------------------------
*Toluene 108-88-3 26-28 100 ppm 100 ppm 22 68
Aliphatic Polyamines Mixture 30-40 Not Established Not Established.
Nonyl Phenol 25154-52-3 30-40 Not
Established. 1 68
*Indicates
toxic chemical(s) subject to reporting requirements of Section 313 of Title III
and of 40 CFR 372.
SECTION 3 - PHYSICAL
DATA
Boiling
Range (Deg.): 230° Vapor
Density: Heavier than air
Evaporation
Rate: Slower than Ether
Percent
Volatile By Volume: 27 Weight
Per Gallon (lbs.): 7.85± .2
SECTION 4 - FIRE &
EXPLOSION HAZARD DATA
Flash Point (Deg.
F): 80° Lower
Explosive Limit: 1.2
Extinguishing
Media: Foam, alcohol foam, CO2, dry
chemical,
OSHA
Flammability Classification: Flammable
Liquid IC
Special
Firefighting Procedures: Wear a
NIOSH/MSHA approved self contained breathing apparatus
and
full protective clothing. Use water to
keep fire exposed containers cool. Water
may be ineffective as an
extinguishing
agent.
Unusual Fire &
Explosion Hazards: Vapors are heavier
than air and may travel along the ground or be moved by ventilation to ignition
sources at locations distant from material handling point. Pressure may build up in containers and
create an explosion hazard.
SECTION 5 - HEALTH
HAZARD DATA
THIS PRODUCT IS FLAMMABLE
Effects Of Overexposure:
Eyes: Irritation, burning, tearing and redness.
Skin: Moderate irritation or defatting of skin upon
prolonged or repeated contact.
Ingestion: Abdominal pain, nausea, vomiting and
diarrhea.
Inhalation: Excessive exposure to vapors can cause
headache, dizziness, uncoordination, nausea and loss of consciousness.
Emergency & First Aid Procedures:
Cont. Section 5 - Health Hazard
Data
Eyes: Flush with water for 15 minutes.
Skin: Remove contaminated clothing, wash skin with
soap and water.
Ingestion: Do not induce
vomiting. Get medical attention
immediately.
Inhalation: Move to fresh air, aid breathing if
necessary.
In all cases, consult a physician for best treatment.
Chemical listed as
carcinogen or potential carcinogen:
NTP: No
IARC: No OSHA: No
SECTION 6 - REACTIVITY
DATA
Stability: Product
Stable
Conditions to
Avoid: All sources of ignition
Incompatibility
(Materials to Avoid): Oxidizing agents,
strong acids & bases
Hazardous
Decomposition Products: Carbon monoxide,
carbon dioxide, nitrogen oxides and organic compounds.
Hazardous
Polymerization: Will Not Occur
SECTION 7 - SPILL OR
LEAK PROCEDURES
Steps To Be Taken In
Case Material Is Released Or Spilled:
Dike spill area. Absorb spill
with inert absorbent material. Place in
sealed metal containers for proper disposal.
Waste Disposal
Method: Dispose of in accordance with
local, state and federal regulations.
SECTION 8 - SPECIAL
PROTECTION INFORMATION
Respiratory
Protection: Use a NIOSH/MSHA jointly
approved respirator
Ventilation: Use mechanical ventilation
Protective
Gloves: Neoprene or rubber
Eye Protection: Chemical splash goggles
Other Protective
Equipment: Protective clothing, barrier
cream, eye bath, safety shower
SECTION 9 - SPECIAL
PRECAUTIONS
Precautions To Be
Taken In Handling & Storing; Store
in dry area. Keep away from open flames
and high temperatures.
Other Precautions: Minimize contact. Avoid breathing vapors. Practice good industrial hygiene and safe
working practices.