Thermcoat

Select Coat

Color Sealer

PC 155 Primer

Primer 120

Patching Compound

Excel Coat 300

Acrylic Lacquer

Glaze

Hydrothane II

Mechanical Equipment Room (M.E.R.) Coating

Excel-Coat Hydrothane II      Data Sheet

Clear Finish Coat

COMPOSITION:

Excel-Coat Hydrothane II is a multi-purpose, single-component, high quality, low odor, and water borne clear urethane topcoat/sealer.

BASIC USE:

Excel-Coat Hydrothane II is specifically designed to provide a clear finish coat for interior or exterior areas such as walking decks, balconies, patios, stairways, driveways and pool areas. Suitable substrates for the Excel-Coat Hydrothane II Finish Coat are existing Excel-Coat waterproofing systems such as two-tone textures, Excel-Coat KD systems as well as other waterproofing membranes and concrete surfaces. Excel-Coat Hydrothane II Finish Coat provides durable protection and allows easy maintenance of the surface.

TECHNICAL DATA:

LIMITATIONS:

• Do not apply in constantly submerged conditions such as reflecting ponds or tank linings.

• Do not apply over non-structural lightweight concrete without prior written approval.

GRADE:

The Excel-Coat Hydrothane II Finish Coat is a water borne urethane resin to be used as a topcoat. This finish coat can be used with all Excel-Coat systems.

PACKAGING:

The Excel-Coat Hydrothane II Finish Coat is available in 1 and 5 gallon containers (U.S. gallon measures).

SHELF LIFE:

Twelve months from shipping date stored below 80°. Do not allow product to freeze.

COLORS:

Excel-Coat Hydrothane II Finish Coat is a clear topcoat. Excel-Coat Hydrothane II can be tinted for a long-lasting color seal coat.

JOB CONDITIONS:

Before any work is started, the applicator shall thoroughly examine all surfaces for any deficiencies. Should any deficiencies exist, the architect, owner or general contractor shall be notified in writing and any corrections necessary shall be made.

Cold or inclement weather will affect the cure time of all Excel-Coat products. Do not install over wet substrate, in the rain or, if the threat of rain exists within 24 hours.

INSTALLATION:

Preparation:

1. Curing of concrete shall be by means of water cure or dissipating compounds. Curing compounds shall be approved by an authorized representative of Excellent Coatings, Inc.

   Concrete shall be cured a minimum of 21 days prior to installation of the Excel-Ccoat Hydrothane II Finish Coat unless approved by an authorized representative of Excellent Coatings, Inc.

   Concrete finish shall be a power metal float followed by a light steel trowel and fine hair broom finish, or equivalent.

   Concrete surfaces shall be free of excessive roughness, voids, protrusions or exposed aggregate.

   All tooled joints and control joints shall be caulked with a sealant approved by Excellent Coatings, Inc. Moving structural cracks shall be routed, primed and filled with a two-part semi-rigid epoxy.

   To topcoat existing systems, the system must be thoroughly cleaned (power washing with a detergent like Prosoco 2010 All Purpose Cleaner or an organic citrus cleaner is acceptable) and primed.

2. All decks shall be properly sloped to freely drain and eliminate the ponding of water. All expansion joints shall be treated as specified in the drawings and in strict accordance with Excellent Coatings, Inc.'s written instructions. Excellent Coatings, Inc. shall be consulted for specific design requirements.

Application:

STORAGE AND HANDLING:

Store Excel-Coat Hydrothane II in a cool, dry area and protect from freezing. It will be necessary to stir Excel-Coat Hydrothane II before using. Partial containers can be resealed. Should a top skin develop on the remaining contents of a container, the physical properties and effectiveness of the contents will not be impaired. Clean mixing and application tools with water. Dispose of empty containers properly according to current Local, State and Federal regulations.

HEALTH AND HAZARD INFORMATION:

Use the product with adequate ventilation and personal protection. Users must read container label and Material Safety Data Sheet (MSDS) for specific health and safety precautions prior to use.

AVAILABILITY:

Immediately available from Excellent Coatins, Inc. and their authorized distributors.

COST:

Cost data is available from your local Excellent Coatings, Inc. authorized representative. For the name and number of the nearest local representative, call Excellent Coatings, Inc. at (800) 473-3817.

MAINTENANCE:

Cleaning can be accomplished by scrubbing with detergent soap and water. Heavy stains may require a TSP solution and brushing with a stiff broom. Organic Citrus cleaners may be used on the Excel-Coat systems.

GUARANTEE/ WARRANTY:

Excellent Coatings, Inc. warrants Excel-Coat Hydrothane II to be free of defects and manufactured to meet published physical properties for a period of one year following the date of shipment, provided that the product has been applied according to the manufacturer's instructions. Under this warranty, Excellent Coatings, Inc. will provide, at no charge, product in containers to replace any product proved to be defective in applications recommended by us as suitable for this product. All claims concerning the products' defects must be made within twelve months of shipment and within thirty days of discovery. Absence of such claims in writing during this period will constitute a waiver of all claims with respect to such product. This warranty is IN LIEU OF any and all other warranties, expressed or implied, including, but not limited to, any implied warranty of MERCHANTABILITY of fitness for a specific purpose.

TECHNICAL SERVICE:

Authorized local representatives are available to provide design assistance and on-site instruction for our products. Excellent Coatings, Inc. provides assistance in design and development of special applications and partial inspection. Part-time and full-time inspection and instruction are available on a fee basis upon arrangement. Technical Data available upon request.

10/01